check engine light NISSAN PATROL 2004 Electronic Repair Manual

6 CHECK COMBINATION METER
Refer to EL section.
OK or NG
OKcGO TO 11.
NGcReplace combination meter.
7 CHECK HEADLAMP FUNCTION
1. Start engine.
2. Lighting switch ªONº at 2nd position.
3. Check that headlamp high beams are illuminated.
OK or NG
OKcGO TO 8.
NGcCheck headlamp circuit. Refer to EL section.
8 CHECK HEADLAMP INPUT SIGNAL CIRCUIT
1. Stop engine.
2. Disconnect combination meter harness connector.
3. Disconnect combination switch harness connector.
4. Check harness continuity between combination switch terminals 6, 7 and combination meter terminal 26.
SEC014E
MTBL1596
5. Also check harness for short to ground and short to power.
OK or NG
OKcGO TO 10.
NGcGO TO 9.
9 DETECT MALFUNCTIONING PART
Check the following.
+Harness connectors E127, M21
+Diode E108
+Harness for open or short between combination switch and combination meter
cRepair open circuit or short to ground or short to power.
ELECTRICAL LOAD SIGNALTB48DE A/T
Diagnostic Procedure (Cont'd)
EC-4020

6 CHECK COMBINATION METER
Refer to EL section.
OK or NG
OKcGO TO 11.
NGcReplace combination meter.
7 CHECK HEADLAMP FUNCTION
1. Start engine.
2. Lighting switch ªONº at 2nd position.
3. Check that headlamp high beams are illuminated.
OK or NG
OKcGO TO 8.
NGcCheck headlamp circuit. Refer to EL section.
8 CHECK HEADLAMP INPUT SIGNAL CIRCUIT
1. Stop engine.
2. Disconnect combination meter harness connector.
3. Disconnect combination switch harness connector.
4. Check harness continuity between combination switch terminals 6, 7 and combination meter terminal 26.
SEC014E
MTBL1596
5. Also check harness for short to ground and short to power.
OK or NG
OKcGO TO 10.
NGcGO TO 9.
9 DETECT MALFUNCTIONING PART
Check the following.
+Harness connectors E127, M21
+Diode E108
+Harness for open or short between combination switch and combination meter
cRepair open circuit or short to ground or short to power.
ELECTRICAL LOAD
SIGNALTB48DE A/T (WITH EURO-OBD)
Diagnostic Procedure (Cont'd)
EC-4029

CONSULT-II Reference Value in Data Monitor
Mode
Remarks:
+Speci®cation data are reference values.
+Speci®cation data are output/input values which are detected or supplied by the ECM at the connector.
* Speci®cation data may not be directly related to their components signals/values/operations.
MONITOR ITEM CONDITION SPECIFICATION
CKPSzRPM (TDC)
+Run engine and compare CONSULT-II value with the tachometer indication.Almost the same speed as the
tachometer indication.
CMPSzRPM-PUMP
COOLAN TEMP/S+Engine: After warming up More than 70ÉC (158ÉF)
VHCL SPEED SE+Turn drive wheels and compare CONSULT-II value with the speedometer indicationAlmost the same speed as the
speedometer indication
FUEL TEMP SEN+Engine: After warming up More than 40ÉC (104ÉF)
ACCEL POS SEN+Ignition switch: ON
(Engine stopped)Accelerator pedal: fully released 0.40 - 0.60V
Accelerator pedal: fully depressed Approx. 4.5V
FULL ACCEL SW+Ignition switch: ON
(Engine stopped)Accelerator pedal: fully depressed ON
Except above OFF
ACCEL SW (FC)+Ignition switch: ON
(Engine stopped)Accelerator pedal: fully released CLOSE
Accelerator pedal: slightly open OPEN
OFF ACCEL SW+Ignition switch: ON
(Engine stopped)Accelerator pedal: fully released ON
Accelerator pedal: slightly open OFF
SPILL/V+Engine: After warming up Approx. 13ÉCA
BATTERY VOLT+Ignition switch: ON (Engine stopped) 11 - 14V
P/N POSI SW+Ignition switch: ONShift lever: Park/Neutral ON
Except above OFF
START SIGNAL+Ignition switch: ON®START®ON OFF®ON®OFF
AIR COND SIG+Engine: After warming up, idle the
engineAir conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates.)ON
BRAKE SW+Ignition switch: ONBrake pedal: depressed ON
Brake pedal: released OFF
IGN SW+Ignition switch: ON®OFF ON®OFF
WARM UP SW+Ignition switch: ONHeat up switch: ON ON
Heat up switch: OFF OFF
MAS AIR/FL SE+Ignition switch: ON (Engine stopped) Approx. 0.4V
+Engine: After warming up
+Air conditioner switch: OFF
+Shift lever: Neutral position
+No-loadIdle 1.5 - 1.9V
Engine is revving from idle to about 4,000
rpm1.5 - 1.9 to Approx. 4.0V (Check for
liner voltage rise in response to
engine being increased to about
4,000 rpm.)
DECELER F/CUT+Engine: After warming up Idle OFF
INJ TIMG C/V+Engine: After warming up, idle the engine. Approx. 50 - 70%
AIR COND RLY+Engine: After warming up, idle the
engineAir conditioner switch: OFF OFF
Air conditioner switch: ON
(Compressor operates.)ON
GLOW RLY+Refer to EC-252 in Service Manual (Publication No. SM9E-Y61CG3).
COOLING FAN+When cooling fan is stopped. OFF
+When cooling fan operates. ON
TROUBLE DIAGNOSIS Ð GENERAL DESCRIPTIONZD30DDTi
EC-4038

<SUPPLEMENT-IV> ELECTRICALSYSTEM
SECTION
EL
When you read wiring diagrams:
+ Read GI section, ªHOW TO READ WIRING DIAGRAMSº.
When you perform trouble diagnoses, read GI section, ªHOW TO FOLLOW FLOW
CHART IN TROUBLE DIAGNOSESº and ªHOW TO PERFORM EFFICIENT DIAGNOSIS
FOR AN ELECTRICAL INCIDENTº.
+ Check for any service bulletins before servicing the vehicle.
MODIFICATION NOTICE:
+ Wiring Diagrams have been changed.
CONTENTS
POWER SUPPLY ROUTING/WAGON AND
HARDTOP MODELS .................................................4005
Schematic ..............................................................4005
Wiring Diagram Ð POWER Ð..............................4006
GROUND DISTRIBUTION/WAGON AND
HARDTOP MODELS .................................................4016
Main Harness/LHD Models....................................4016
Main Harness/RHD Models ...................................4019
Engine Room Harness/LHD Models .....................4022
Engine Room Harness/RHD Models .....................4024
Body Harness/LHD Models ...................................4026
Body Harness/RHD Models...................................4028
Body No. 2 Harness/LHD Models .........................4030
Body No. 2 Harness/RHD Models.........................4031
Back Door and Rear Window Defogger Harness/
LHD Models ...........................................................4032
Back Door and Rear Window Defogger Harness/
RHD Models ..........................................................4033
COMBINATION SWITCH ...........................................4034
Check .....................................................................4034
STEERING SWITCH ..................................................4036
Check/RHD Models for Europe and LHD Models.4036
Check/RHD Models Except for Europe .................4038
HEADLAMP/WAGON AND HARDTOP MODELS
Ð Conventional Type Ð ..........................................4040
Wiring Diagram Ð H/LAMP Ð ..............................4040
HEADLAMP/WAGON AND HARDTOP MODELS
Ð Xenon Type Ð ......................................................4041
Bulb Replacement .................................................4041
Wiring Diagram Ð H/LAMP Ð ..............................4042 HEADLAMP/WAGON AND HARDTOP MODELS
Ð Headlamp Aiming Control Ð
.............................4044
Wiring Diagram Ð H/AIM Ð/Except for the
Middle East ............................................................4044
HEADLAMP/WAGON AND HARDTOP MODELS
Ð Daytime Light System Ð ....................................4047
Wiring Diagram Ð DTRL Ð ..................................4047
PARKING, LICENSE AND TAIL LAMPS/WAGON
AND HARDTOP MODELS ........................................4049
Wiring Diagram Ð TAIL/L Ð/Type A .....................4049
Wiring Diagram Ð TAIL/L Ð/Type B.....................4051
Wiring Diagram Ð TAIL/L Ð/Type C ....................4053
BACK-UP LAMP/WAGON AND HARDTOP
MODELS ....................................................................4055
Wiring Diagram Ð BACK/L Ð/LHD Models
Except TB48 Engine with A/T................................4055
Wiring Diagram Ð BACK/L Ð/LHD Models for
TB48 Engine with A/T ............................................4056
Wiring Diagram Ð BACK/L Ð/RHD Models
Except TB48 Engine with A/T................................4057
Wiring Diagram Ð BACK/L Ð/RHD Models
for TB48 Engine with A/T ......................................4058
STOP LAMP/WAGON AND HARDTOP MODELS ...4059
Wiring Diagram Ð STOP/L Ð/Type A ..................4059
Wiring Diagram Ð STOP/L Ð/Type B ..................4060
FRONT FOG LAMP/WAGON AND HARDTOP
MODELS ....................................................................4061
Wiring Diagram Ð F/FOG Ð/Except for Europe
and China ..............................................................4061
EL-4001

Self-Diagnosis Function
DESCRIPTION
+Diagnosis function consists of the self-diagnosis mode performed automatically and the CONFIRMATION/
ADJUSTMENT mode operated manually.
+ Self-diagnosis mode checks for connections between the units constituting this system, analyzes each
individual unit at the same time, and displays the results on the LCD screen.
+ CONFIRMATION/ADJUSTMENT mode is used to perform trouble diagnosis that require operation and
judgment by an operator (malfunction that cannot be automatically judged by the system), to check/change
the set value, and to display the History of Errors of the navigation system.
DIAGNOSIS ITEM
Mode Description
Self-diagnosis +
NAVI Control unit diagnosis (DVD-ROM drive will not be diagnosed when no
map DVD-ROM is in it.).
+ Performs diagnosis of each unit and connections between control unit and
GPS antenna, as well as between control unit and each unit.
Con®rmation/
Adjustment Display
Color tone and shading of the screen can be checked by the display of a color
bar and a gray scale.
Vehicle signals Analyzes the following vehicle signals: Vehicle speed signal, light signal, ignition
switch signal, and reverse signal.
Navigation Display Longi-
tude & Lati-
tude
Display the map. Use the joystick to adjust position. Longitude and latitude will be
displayed.
Speed Calibra-
tion Under ordinary conditions, the navigation system distance measuring function will
automatically compensate for minute decreases in wheel and tire diameter
caused by tire wear or low-pressure. Speed calibration immediately restores sys-
tem accuracy in cases such as when distance calibration is needed because of
the use of tire chains in inclement weather.
Angle Adjust-
ment Corrects difference between actual turning angle of a vehicle and turning angle of
the car mark on the display.
Initialize Loca-
tion This mode is for initializing the current location. Use when the vehicle is trans-
ported a long distance on a trailer, etc.
History of Errors Diagnosis results previously stored in the memory (before turning ignition switch
ON) are displayed in this mode. Time and location when/where the errors
occurred are also displayed.
Self-Diagnosis Mode
OPERATION PROCEDURE
1. Start the engine.
2. Push and hold ªMAPº and ªDAY/NIGHTº switches simulta-
neously for 5 seconds or more.
+ Push the ªBACKº switch and the initial system screen will
be shown.
PKIB1537E
NAVIGATION SYSTEM
EL-4189

3. CHECK VEHICLE SPEED SIGNAL
1. Connect NAVI control unit and combination meter connector.
2. Start engine and drive vehicle at more than 40 km/h (25 MPH).
3. Check the signal between NAVI control unit harness connector M168 terminal 28 (R/W) and ground with CONSULT-ll oroscilloscope.
SKIA9106E
28 (R/W) - Ground: Refer to EL-4183. OK or NG
OK ©Replace NAVI control unit.
NG ©Replace uni®ed meter control unit.
ILLUMINATION SIGNAL CHECK
1. CHECK TAIL LAMP OPERATION
When lighting switch turned 1st or 2nd position, does tail lamp illuminate?
YesorNo
Ye s ©GO TO 2.
No ©Go to tail lamp trouble diagnosis.
2. CHECK ILLUMINATION SIGNAL
Check voltage between NAVI control unit and ground.
SKIB0315E
OK or NG
OK ©Replace NAVI control unit.
NG ©Repair harness or connector.
Terminals
Lighting switch position Voltage
(+)
(þ)
Connector Terminal (wire color)
M168 25 (L/B) Ground 1st or 2nd position Battery voltage
OFF Approx. 0V
NAVIGATION SYSTEM
Trouble Diagnoses (Cont'd)
EL-4207

A
A/C operational check ................................HA-4032
A/C self-diagnoses (auto A/C)....................HA-4025
A/C, A - Wiring diagram .............................HA-4009
A/CCUT - Wiring diagram ..........................EC-4058
Air cleaner ®lter replacement .....................MA-4003
Air ¯ow meter - See Mass air ¯ow
sensor .....................................................EC-4047
Air mix. door motor.....................................HA-4036
Antenna .......................................................EL-4164
ASCD (automatic speed control
device) .....................................................EL-4233
ASCD - Wiring diagram ..............................EL-4234
A/T - Wiring diagram ...................................AT-4003
A/T trouble diagnoses .................................AT-4011
A/T Wiring diagram AT - NONDTC .............AT-4012
Audio ...........................................................EL-4136
AUDIO - Wiring diagram .............................EL-4137
Audio and A/C control removal and
installation - See Instrument panel .........BT-4006
Auto air conditioner - Wiring diagram ........HA-4009
Automatic speed control system - See
ASCD ......................................................EL-4233
AV and NAVI control unit ............................EL-4164
B
Back-up lamp ..............................................EL-4055
BACK/L - Wiring diagram............................EL-4055
Blower motor ..............................................HA-4038
Bumper, front ..............................................BT-4002
Bumper, rear ...............................................BT-4005
C
Camshaft ....................................................EM-4003
CHIME - Wiring diagram .............................EL-4113
Combination meter......................................EL-4095
Combination meter removal and instal-
lation - See Instrument panel..................BT-4006
Combination switch .....................................EL-4034
COMPAS - Wiring diagram .........................EL-4099
Console box - See Instrument panel ..........BT-4006
CONSULT-II general information.................GI-4002
Cruise control - See ASCD .........................EL-4233
Cylinder head .............................................EM-4016
D
Daytime light system...................................EL-4047
DEF - Wiring diagram .................................EL-4126
DEICER - Wiring diagram...........................EL-4125
Dimensions ..................................................GI-4008
D/LOCK - Wiring diagram ...........................EL-4245Dome light - See Interior lamp ...................EL-4088
DTRL - Wiring diagram ...............................EL-4047
E
ECM input/output signal .............................EC-4040
Electrical load signal circuit ...EC-4008, 4016, 4025
Electrical units location ...............................EL-4300
Engine control circuit
diagram .............................EC-4003, 4005, 4013,
4022, 4037, 4059
Exhaust system ..........................................FE-4008
Exterior ........................................................BT-4009
F
F/FOG - Wiring diagram .............................EL-4061
FICD - Wiring diagram ...............................EC-4036
Fog lamp, front............................................EL-4061
Fog lamp, rear ............................................EL-4064
Front bumper ..............................................BT-4002
Front fog lamp.............................................EL-4061
Front washer ...............................................EL-4117
Front wiper ..................................................EL-4117
Fuel gauge ..................................................EL-4095
Fuse ..............................................................Foldout
Fusible link....................................................Foldout
G
Gauges........................................................EL-4095
GLOW - Wiring diagram.............................EC-4033
GPS antenna ..............................................EL-4164
Ground distribution......................................EL-4016
H
Harness layout ..................................EL-4307, 4308
Headlamp ....................................................EL-4040
Headlamp washer .......................................EL-4122
Heat up switch............................................EC-4054
Heated seat.................................................EL-4231
HEATUP - Wiring diagram .........................EC-4054
Height (Dimensions) ....................................GI-4008
H/LAMP - Wiring diagram ...........................EL-4040
HLC - Wiring diagram .................................EL-4122
Hood............................................................BT-4002
Horn ............................................................EL-4124
HORN - Wiring diagram..............................EL-4124
HSEAT - Wiring diagram.............................EL-4231
I
ILL - Wiring diagram ...................................EL-4080
ALPHABETICAL INDEX
IDX-4002